The USRP2 only supports Gigabit Ethernet and will not work with a 10/100 Mbps interface. When in safe-mode, the USRP-N device will always have the IP address 192.168.10.2.įor more information on using external tools to unbrick your device when even this fails, see Unbricking an N-Series Device. Continue to hold-down the button until the front-panel LEDs blink and remain solid. To boot into the safe image, hold-down the safe-mode button while power-cycling the device. The safe-mode button is a pushbutton switch (S2) located inside the enclosure. Once booted into the safe image, the user can once again load images onto the device. Fortunately, the USRP-N Series can be booted into a safe (read-only) image. Its possible to put the device into an unusable state by loading bad images. Use this number to select the correct FPGA image for your device. Determine the revision number from the sticker on the rear of the chassis. Note: Different hardware revisions require different FPGA images. The USRP will drop off the network for a brief moment and reboot. If you immediately want to apply this image, add the reset argument: uhd_image_loader -args="type=usrp2,addr=,reset" Use custom-built images: uhd_image_loader -args="type=usrp2,addr=" -fw-path="" -fpga-path="" Use default images: uhd_image_loader -args="type=usrp2,addr=" This ensures that when the device reboots, it has a compatible set of images to boot into. When updating images, always burn both the FPGA and firmware images before power cycling. The USRP-N Series can be reprogrammed over the network to update or change the firmware and FPGA images. Load the Images onto the On-board Flash (USRP-N Series only) Use the card burner tool (Windows) /lib/uhd/utils/usrp2_card_burner_gui.py The list option has been implemented on Linux, Mac OS X, and Windows. The list result will filter out disk partitions and devices too large to be the sd card. Use the -list option to get a list of possible raw devices. usrp2_card_burner.py -dev=/dev/sd -fpga= Use the card burner tool (UNIX) sudo /lib/uhd/utils/usrp2_card_burner_gui.py Cards can have unexpected timing characteristics.įor these reasons, we recommend that you use the SD card that was supplied with the USRP2.Cards can be SDHC, which is not a supported interface.However, certain types of SD cards will not interface with the CPLD: Warning! It is possible to use 3rd party SD cards with the USRP2. Make sure that -dev= specifies the SD card. If you specify the wrong device node, you could overwrite your hard drive. Warning! Use usrp2_card_burner with caution. Load the Images onto the SD card (USRP2 only) Up to 50 MHz of RF BW with 8-bit samples.Up to 25 MHz of RF BW with 16-bit samples.16-bit and 8-bit sample modes (sc8 and sc16).Load the Images onto the On-board Flash (USRP-N Series only).Load the Images onto the SD card (USRP2 only).If you have any questions, please let me know in the comments. If I open up a browser and issue my hostname, I will see the web page that is served by my Raspberry Pi. Now all the traffic coming through port 80 will be redirected to our raspberry pi. For Netgear, it is under Advanced Set Ups.Įnter the private IP address of Raspberry Pi and enter the port as 80 as shown in the image and click on Apply. Login to your router using in IP address with your login credentials. I am using a netgear router and will show you how I did it This will be different for different Routers. In order to forward those packets to raspberry pi with private IP address, in your home network, you will have to do port forwarding in the router. But the requests for your raspberry pi will only reach till your home router. Hostname will be mapped to your Dynamic Public IP address in a regular interval. Here is a list of World’s Best WiFi Routers of the year 2018.Make sure you grab one of them for High speed, Long Range, and Stable Internet connection.ĭynamic DNS is now ready. Port Forwarding on Router Best WiFi Routers of 2018 You will then be asked to login with your No-IP account username and password and it will help you to configure DUC easily. For that Open up the terminal and issue these commands one by oneĬd /usr/local/src/ wget tar xf cd noip-2.1.9-1/ make install In my case, I chose “”ĭownload and Set UP DUC (Dynamic Update Client) Once verification is completed, you can login using you credentials and create a DDNS Hostname for that device. Create an account using a valid E Mail ID and verify it via E Mail. Setting Up NOIP DUC Sign Up on NOIPįirst thing you need is an account in NOIP. Now I am going to setup a NOIP hostname and map it with my IP address so that I can access the webpage, from anywhere around the world, using this domain name. I have a raspberry pi in my home network which is acting as a web server (port 80) which serves a web page of classic 2048 game.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |